Current Affairs
How to Make Rice Puller and Anti Iron Antique ??
SD24 News Network –
Rice extractors are any antique metal object that has the magical potential to extract grains of rice. Rice pullers are made of copper alloys or the element iridium. This type of metal has an inherent electrical or magnetic force that makes it highly valuable.
👇👇Must watch this video👇👇
WHERE ARE THE RICE EXTRACTORS LOCATED?
Rice drawing properties are commonly found in copper and iridium they produced objects such as coins, vessels, glasses and jewelry. These metals are very rare; make it valuable. It has been reported that rice extractors are mostly found in rural areas, remote areas, mostly buried underground.
RICE EXTRACTER USE:
It is used in satellites, rockets and for other navy, army research purposes because they exhibit natural electric or magnetic force.
RP is of particular interest to fraudsters in the Indian subcontinent. It is used to pull off deception with some illusionist tricks. The scam works this way; the vendor tries to sell RP metals by pretending that there is a lucrative market for this so-called magical item. And in the end, the object is sold for a higher price than it is worth.
Rice pullers are believed to have powers that can attract wealth and prosperity to the home.
RICE EXTRACTOR TEST
CLEANING:
Wash the metal or object first with soap and water, then with salt water.
👇👇Must watch this video👇👇
Wash it again with clean water and let it dry.
Clean the item with cotton and newspaper.
Allow the item to return to normal room temperature before starting the rice pull test.
1. STAPLER PIN TEST
Take the Iron Stapler and bring it near the Rice Puller item. The pin should not stick to the metal of the RP and should not repel either. If the stapler pin sticks or bounces, your RP is fake.
2. IMMEDIATE TENSILE TEST
Take rice, preferably husked rice. Keep the rice closer to the object to attract/attract it. Note the time it takes to attract, the distance and the color of the rice.
Instant withdrawal time:
Color Change: Note the time it takes for the rice to change color after being lured.
Drop Time: The time it takes for the rice to fall after being stuck.
3. RICE TO RICE TEST
Take the above tested or sprinkled rice and place it on a flat surface near the untested fresh rice and then check its ductility.
4. A) GLASS WATER TEST:
Fill a non-metallic glass with water and put 4-5 tested rice in the glass (in the corners). After some time, this rice will pile up towards the center. The rice will turn yellow or brown.
Now carry the iron pin above the center of the water; the rice moves away. Remove the iron pin and the rice will go to the center of the back.
If the rice turns blue, then your RP item is fake.
B) WATER TO RICE TEST:
Fill a non-metallic glass with 1 inch of water and place fresh, unhulled, unpeeled rice in the water; it settles to the bottom. Now spread the tested rice/rice powder on the water.
👇👇Must watch this video👇👇
If your metal rice extractor is not fake, the plain rice will start standing vertically on the bottom. They may also appear and adhere to the tested rice dust; hanging underwater.
5. COPPER WIRE TEST
Take a thin copper wire and wind 2-3 turns on the RP item; let the end hang out. Now do the rice pulling test using a copper wire. The wire should attract the rice similar to the RP metal.
6. TORCH TEST
Arrange 2 plastic flashlights, working on pencil cells and with a metal case and a bulb. Remove the flashlight front glass and place it about half an inch from the RP object. Hold another flashlight in a similar manner about 5-10 feet away from the object. Turn on both flashlights.
Keep the iron pin close to the object when performing the torch rice pulling test. If the pin is pulled out by the object during the torch test, then the metal rice puller is fake.
Note the time it takes for the torch that is near the object to dim completely. If it happens within a few minutes, then it is considered good. Also note the second flashlight; still bright or not.
If the light of the flashlight placed near the RP object dims quickly, turn it off and turn it back on after about 2 minutes. If the light remains dim, your flashlight test is successful.
Continue Reading